The short answer
Check seven places before you buy: the rockers, the lower quarter panels, the lower fenders, the bottoms of the doors, the floor pans, the trunk pan and the frame. Those are the places rust is most common. Rust on a bolted-on panel like a fender or a door is the easy fix; rust that has eaten through welded-in metal like the floors, quarters, rockers or frame means cutting and welding, and serious structural rust "can be expensive or even the end of the line" for a car (Autotrader Classics). Don't judge by the paint: the 1967 Mustang fastback I bought in 2020 had paint that looked good, and it still needed new metal in the floors and the front frame rail.
Where to look, what it means, and how big the repair is
Here are the seven, with what to look for at each. Take a flashlight and get underneath: floor rust hides under carpet and insulation, and knocking on a lower panel and listening for a change in pitch tells you whether rust is hiding under filler (The Engine Block).
| Where to look | What rust there means | How big the repair is |
|---|---|---|
| Rockers | The rails and rockers give the body its stiffness from front to back, so rot here is structural (Auto Restorer) | Big. A full rocker can mean taking the doors off and pulling the seats and carpet (MotorWeek); the door opening is braced before cutting so the body can't twist (Auto Restorer) |
| Lower quarter panels | Almost always a problem on older cars; body filler can hide it, and riveted-on patches usually mean the damage underneath is severe (The Engine Block) | Medium to big. A quarter is welded on, so rusted-through metal is cut out and a new panel welded in (Autotrader Classics) |
| Lower fenders | Look for bubbles in the paint or holes just behind the wheel. If you can see through the steel, replace it (Autotrader Classics) | Small, where the fenders bolt on: they are among the easiest panels to replace (Autotrader Classics) |
| Bottoms of the doors | Bubbles or rust holes along the lower door (Autotrader Classics) | Small. Doors bolt on and are among the easiest parts to replace when too far gone (Autotrader Classics) |
| Floor pans | Check under the pedals. A few small rust-through spots may be OK; if you can see the ground, look at another car (Autotrader Classics). A stop sign riveted to the floor is a reason to walk away (The Engine Block) | Medium to big. Rotted floors are cut out and new pans welded in; mine got a whole new floor (below) |
| Trunk pan | Look at the trunk floor (Autotrader Classics) | Medium. It can need extensive work but is possible without major panel replacement (Autotrader Classics); on my fastback the new full floor included it |
| Frame | On a unibody car the subframes are thinner metal and rot quickly; repairs can cost more than the car is worth (The Engine Block) | Biggest. Walk away unless you want a major project (The Engine Block). My fastback's front frame rails were cut out and replaced on a frame table |
What these cars cost to buy is on our 13 classic cars under $10K page; choosing which car to buy is in How to Choose the Perfect Classic Car for You.
What my own two '67s showed
The fastback: good paint, bad floors
I bought my 1967 Mustang fastback in April 2020 from a small Mustang shop in Webb City, Missouri. The sellers didn't sugarcoat it. Even though the paint looked good, it had rust that meant new metal in the floors, the front frame rail, and possibly a rear quarter panel (New Project). It was still "a really solid project, especially for a $14,000 car" (stripped down).


To see everything, I stripped the car and sent the shell to MetalWorks in Eugene, Oregon, to be dipped in acid. That takes off absolutely everything: paint, rust and bondo. It was the final step to really assess which metal needed to be replaced or repaired. If you're starting a rough project, consider an acid dip instead of media blasting (stripped down).
It came back bare metal with quite a bit of rust holes to repair or replace. I ordered a new full floor from Dynacorn to fix the floor and trunk pans (Acid Dipping). Then the front clip came off the body, the old rusty floor and frame rails were cut out, and everything went on a frame table to get it square before welding in new metal (Metal Fabrication).



The 2022 flip coupe: the floors were the good news
In July 2022 I bought a '67 coupe in Butte, Montana, to fix and sell. Its trunk was a reproduction piece and it had a few small metal patches here and there, but the floors, aprons and torque boxes were original with no rust (the flip coupe).
Questions people ask
How do you buy a classic car? Choose the car first (How to Choose the Perfect Classic Car for You), check what it should cost (13 classic cars under $10K), then check the seven places above for rust before you buy.
What goes on a classic car buying checklist? For rust: the rockers, lower quarter panels, lower fenders, door bottoms, floor pans, trunk pan and frame. Get underneath with a light, and knock on the lower panels and listen for a change in pitch that gives away filler (The Engine Block).
What's the best tip for buying a classic car? Don't judge it by the paint. My fastback's paint looked good, and it still needed new metal in the floors and front frame rail (New Project).
Sources
All opened on 19 Nov 2026.
- Classic Cars: Know Where to Look for Rust Before Buying — Autotrader Classics, Ron Moorhead, 19 Mar 2018. Lower doors and fenders, floor under the pedals, trunk floor, bolt-on vs welded-in panels, structural rust.
- 5 Prime Areas to Look for Rust — The Engine Block, Bruce Lindermann, 7 Nov 2018. Quarter panels, floor pans, frame, knocking for filler.
- Replacing Rockers & Frame Components — Auto Restorer, Paul Riccioli Jr., 1 Apr 2013. What rockers and rails do; bracing before cutting.
- Replace your Rockers — MotorWeek, 6 Dec 2018. What a full rocker replacement involves.
- Classic Nation's own posts: New Project – 1967 Mustang Fastback, Getting the '67 Mustang Fastback stripped down, Acid Dipping, Metal Fabrication and New Full Floor Pan Preparation, I picked up this '67 Mustang Coupe to flip.

Comments
No comments yet.